“Iron wires” showing through sidewall











up vote
5
down vote

favorite












I purchased my Suzuki Alto K10 car in 2011. In 2017, I fitted the stepney (AKA "spare tyre") and have driven almost 15000km.



Recently I have observed some iron wires came from side wall of this tyre, which I have taken out.



Is this tyre dangerous? Should it be replaced?










share|improve this question









New contributor




NBV Mani is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
















  • 4




    Welcome to Motor Vehicle Maintenance & Repair! I completely agree with what motosubatsu stated in their answer. I would, however, like to state, if you only have 15kkm on the tires, you have an underlying problem with your car. You need to ensure the alignment is good and that all of the underpinnings on the vehicle are in good shape. Even the cheapest tires you can find should be lasting you longer than 15kkm. If you replace the bad tire(s) with a new one, more than likely it will just end up ruined in short order.
    – Pᴀᴜʟsᴛᴇʀ2
    yesterday






  • 13




    A picture of the tire with the visible wires sure would be helpful. Barring that, it's safest to assume it's the tire cords and bad things are happening.
    – Ellesedil
    yesterday






  • 6




    You say "...which I have taken out.". Normally the steel belts inside a tire can't just be "taken out". Did you run over something or is the tire so worn down in that area that the steel belts are showing? Also, there are typically not steel wires in the sidewall. I think we might have some meaning lost in translation here.
    – JPhi1618
    yesterday








  • 4




    Possible duplicate of What is this wire in my tyre?
    – SeanC
    yesterday










  • I suppose OP fitted not a real tire, but a limited-use donut. 15000km's ago.
    – Martin
    18 hours ago

















up vote
5
down vote

favorite












I purchased my Suzuki Alto K10 car in 2011. In 2017, I fitted the stepney (AKA "spare tyre") and have driven almost 15000km.



Recently I have observed some iron wires came from side wall of this tyre, which I have taken out.



Is this tyre dangerous? Should it be replaced?










share|improve this question









New contributor




NBV Mani is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
















  • 4




    Welcome to Motor Vehicle Maintenance & Repair! I completely agree with what motosubatsu stated in their answer. I would, however, like to state, if you only have 15kkm on the tires, you have an underlying problem with your car. You need to ensure the alignment is good and that all of the underpinnings on the vehicle are in good shape. Even the cheapest tires you can find should be lasting you longer than 15kkm. If you replace the bad tire(s) with a new one, more than likely it will just end up ruined in short order.
    – Pᴀᴜʟsᴛᴇʀ2
    yesterday






  • 13




    A picture of the tire with the visible wires sure would be helpful. Barring that, it's safest to assume it's the tire cords and bad things are happening.
    – Ellesedil
    yesterday






  • 6




    You say "...which I have taken out.". Normally the steel belts inside a tire can't just be "taken out". Did you run over something or is the tire so worn down in that area that the steel belts are showing? Also, there are typically not steel wires in the sidewall. I think we might have some meaning lost in translation here.
    – JPhi1618
    yesterday








  • 4




    Possible duplicate of What is this wire in my tyre?
    – SeanC
    yesterday










  • I suppose OP fitted not a real tire, but a limited-use donut. 15000km's ago.
    – Martin
    18 hours ago















up vote
5
down vote

favorite









up vote
5
down vote

favorite











I purchased my Suzuki Alto K10 car in 2011. In 2017, I fitted the stepney (AKA "spare tyre") and have driven almost 15000km.



Recently I have observed some iron wires came from side wall of this tyre, which I have taken out.



Is this tyre dangerous? Should it be replaced?










share|improve this question









New contributor




NBV Mani is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.











I purchased my Suzuki Alto K10 car in 2011. In 2017, I fitted the stepney (AKA "spare tyre") and have driven almost 15000km.



Recently I have observed some iron wires came from side wall of this tyre, which I have taken out.



Is this tyre dangerous? Should it be replaced?







tires sidewall-damage






share|improve this question









New contributor




NBV Mani is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.











share|improve this question









New contributor




NBV Mani is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.









share|improve this question




share|improve this question








edited 10 hours ago









FreeMan

1286




1286






New contributor




NBV Mani is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.









asked yesterday









NBV Mani

2612




2612




New contributor




NBV Mani is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.





New contributor





NBV Mani is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.






NBV Mani is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.








  • 4




    Welcome to Motor Vehicle Maintenance & Repair! I completely agree with what motosubatsu stated in their answer. I would, however, like to state, if you only have 15kkm on the tires, you have an underlying problem with your car. You need to ensure the alignment is good and that all of the underpinnings on the vehicle are in good shape. Even the cheapest tires you can find should be lasting you longer than 15kkm. If you replace the bad tire(s) with a new one, more than likely it will just end up ruined in short order.
    – Pᴀᴜʟsᴛᴇʀ2
    yesterday






  • 13




    A picture of the tire with the visible wires sure would be helpful. Barring that, it's safest to assume it's the tire cords and bad things are happening.
    – Ellesedil
    yesterday






  • 6




    You say "...which I have taken out.". Normally the steel belts inside a tire can't just be "taken out". Did you run over something or is the tire so worn down in that area that the steel belts are showing? Also, there are typically not steel wires in the sidewall. I think we might have some meaning lost in translation here.
    – JPhi1618
    yesterday








  • 4




    Possible duplicate of What is this wire in my tyre?
    – SeanC
    yesterday










  • I suppose OP fitted not a real tire, but a limited-use donut. 15000km's ago.
    – Martin
    18 hours ago
















  • 4




    Welcome to Motor Vehicle Maintenance & Repair! I completely agree with what motosubatsu stated in their answer. I would, however, like to state, if you only have 15kkm on the tires, you have an underlying problem with your car. You need to ensure the alignment is good and that all of the underpinnings on the vehicle are in good shape. Even the cheapest tires you can find should be lasting you longer than 15kkm. If you replace the bad tire(s) with a new one, more than likely it will just end up ruined in short order.
    – Pᴀᴜʟsᴛᴇʀ2
    yesterday






  • 13




    A picture of the tire with the visible wires sure would be helpful. Barring that, it's safest to assume it's the tire cords and bad things are happening.
    – Ellesedil
    yesterday






  • 6




    You say "...which I have taken out.". Normally the steel belts inside a tire can't just be "taken out". Did you run over something or is the tire so worn down in that area that the steel belts are showing? Also, there are typically not steel wires in the sidewall. I think we might have some meaning lost in translation here.
    – JPhi1618
    yesterday








  • 4




    Possible duplicate of What is this wire in my tyre?
    – SeanC
    yesterday










  • I suppose OP fitted not a real tire, but a limited-use donut. 15000km's ago.
    – Martin
    18 hours ago










4




4




Welcome to Motor Vehicle Maintenance & Repair! I completely agree with what motosubatsu stated in their answer. I would, however, like to state, if you only have 15kkm on the tires, you have an underlying problem with your car. You need to ensure the alignment is good and that all of the underpinnings on the vehicle are in good shape. Even the cheapest tires you can find should be lasting you longer than 15kkm. If you replace the bad tire(s) with a new one, more than likely it will just end up ruined in short order.
– Pᴀᴜʟsᴛᴇʀ2
yesterday




Welcome to Motor Vehicle Maintenance & Repair! I completely agree with what motosubatsu stated in their answer. I would, however, like to state, if you only have 15kkm on the tires, you have an underlying problem with your car. You need to ensure the alignment is good and that all of the underpinnings on the vehicle are in good shape. Even the cheapest tires you can find should be lasting you longer than 15kkm. If you replace the bad tire(s) with a new one, more than likely it will just end up ruined in short order.
– Pᴀᴜʟsᴛᴇʀ2
yesterday




13




13




A picture of the tire with the visible wires sure would be helpful. Barring that, it's safest to assume it's the tire cords and bad things are happening.
– Ellesedil
yesterday




A picture of the tire with the visible wires sure would be helpful. Barring that, it's safest to assume it's the tire cords and bad things are happening.
– Ellesedil
yesterday




6




6




You say "...which I have taken out.". Normally the steel belts inside a tire can't just be "taken out". Did you run over something or is the tire so worn down in that area that the steel belts are showing? Also, there are typically not steel wires in the sidewall. I think we might have some meaning lost in translation here.
– JPhi1618
yesterday






You say "...which I have taken out.". Normally the steel belts inside a tire can't just be "taken out". Did you run over something or is the tire so worn down in that area that the steel belts are showing? Also, there are typically not steel wires in the sidewall. I think we might have some meaning lost in translation here.
– JPhi1618
yesterday






4




4




Possible duplicate of What is this wire in my tyre?
– SeanC
yesterday




Possible duplicate of What is this wire in my tyre?
– SeanC
yesterday












I suppose OP fitted not a real tire, but a limited-use donut. 15000km's ago.
– Martin
18 hours ago






I suppose OP fitted not a real tire, but a limited-use donut. 15000km's ago.
– Martin
18 hours ago












4 Answers
4






active

oldest

votes

















up vote
24
down vote













The "wires" you mention are likely the tire cords - essentially bands of steel wire that are major structural elements of the tire's construction. If they are exposed this is an indicator of imminent failure and the tire is dangerous to be used.



If the cords are showing through the sidewall:





  • DO NOT drive the vehicle with that tire on!


  • DO Get the tire replaced ASAP!


  • DO NOT attempt to "remove" the cords!






share|improve this answer





















  • You might also note that, like Paulster noted in the comments, 150,000 km is really early to be having this problem. The OP might consider looking for the underlying reason here.
    – Cullub
    yesterday






  • 3




    @Cullub according to OP, it's 15,000 km which is even earlier for this type of problem. However, it's not that early for a spare (especially if it's a compact spare), as the OP mentioned he was running. That was edited out of the OP and missed by most of us.
    – FreeMan
    13 hours ago










  • @Freeman - that's a very good point, I must confess I edited quite quickly yesterday and my initial research into the term "stepny" was unsuccessful so I left it out. I've voted to approve your edit restoring that information.
    – motosubatsu
    13 hours ago


















up vote
5
down vote













Sidewall damage is almost unrepairable. If it is indeed damage to the steel belts, the tire will fail violently (instantly) soon in the future.



That's a good reason not to be trying to change it on the car, because that involves a lot of direct handling of the tire. Tires can blow from handling/maintenance, and do hurt people handling them; that's why you may see your tire shop inflate tires inside a very tough cage. If he's afraid of a new tire, do the math.. But it's pretty safe in your wheelwell. So with a structurally damaged tire, ask yourself "is this handling necessary?"



Of course it's much more dangerous to drive the car normally at-speed and have a blowout cause a loss of control or vehice rollover.



But don't let the chicken littles fool you, you can limp the car to the tire shop. It's vital to keep speed down to a speed where you won't lose control when the tire violently fails, 20 mph (30 kph) will be absolutely fine. If you go much faster, energy in speed is a square function, so you have a wildly increasing chance of loss of control, rollover, colliding with other cars, hurting yourself and others, and wrecking the car of course.



Also, very important: don't just get on the main road at any speed. Don't let yourself into a situation wher you say "I am going fast because I have to", avoid those roads. Work your way through side/back streets; a longer route is fine. Choose roads where you will be able to stop immediately without disrupting traffic too badly, and once the tire is blown, you can safely handle it without fear (except of sharp edges) and put on the spare on. This will not be a normal soft tire, if you press onward for even 0.1mi (0.2km) you will quickly destroy the wheel. Road conditions won't care; I've been in places where you had to drive another 2km to get to a safe place to change a tire, and just had to let the wheel be wrecked. Don't select roads like that.






share|improve this answer



















  • 3




    You could also use the spare...
    – Cullub
    yesterday










  • Sure, but why change it when you don't have to...
    – Harper
    22 hours ago






  • 5




    In my local jurisdiction, a good reason to fit the spare would be to avoid prosecution and a fine.
    – Steve Matthews
    19 hours ago






  • 1




    @Cullub Looks like the OP has already used the spare tire, or the "stepney" (that part has been edited out of the question). I guess that the OP does not have another spare, so using the spare is out of the question.
    – fortunate_man
    14 hours ago






  • 1




    @Harper valid points I hadn't considered. I still stand by my point with one caveat - deflate the tire first. Problem solved. Unfortunately, yelling exploding tires is not helping people overcome their DIY fear, and changing a tire is simple and can save a lot of time and money. Frankly, it strikes me as "chicken little"... Like anything in life, there are simple precautions to be taken to minimize the danger. FWIW, I did upvote your answer and did so before my comment or your response.
    – FreeMan
    13 hours ago


















up vote
1
down vote













To reiterate what Pᴀᴜʟsᴛᴇʀ2 said in the comment, such side-wall damage is not supposed to happen under normal conditions. You should try to discover what the problem was before fitting new tyres, otherwise you risk ruining those as well:




  • check the production date of your current tyres. Were they produced in 2016/2017, or much earlier? Could be the case if you got them second-hand.

  • check the camber angle. Excessive camber (which can be easily seen) may contribute to sidewall damage

  • check the load index and speed rating of your tires. With a 1.2 ton car, your tires should be at least 75S.

  • check the inflation pressure. Driving with under-inflated tyres could ruin then quite quickly.


And yeah, once the steel cord breaks, the tyres are beyond repair and quite dangerous to drive on. On turn you take there's a risk that the cord will puncture the tyre, sending your car off the road.






share|improve this answer






























    up vote
    -3
    down vote













    You can not pull the steel tire belts out; You might be able to cut them with good wire cutters. Could you have picked up nails somewhere? I have pulled nails out of tread but never a side wall. In the tread, the heads have worn away so it becomes a "wire".






    share|improve this answer





















      Your Answer








      StackExchange.ready(function() {
      var channelOptions = {
      tags: "".split(" "),
      id: "224"
      };
      initTagRenderer("".split(" "), "".split(" "), channelOptions);

      StackExchange.using("externalEditor", function() {
      // Have to fire editor after snippets, if snippets enabled
      if (StackExchange.settings.snippets.snippetsEnabled) {
      StackExchange.using("snippets", function() {
      createEditor();
      });
      }
      else {
      createEditor();
      }
      });

      function createEditor() {
      StackExchange.prepareEditor({
      heartbeatType: 'answer',
      convertImagesToLinks: false,
      noModals: true,
      showLowRepImageUploadWarning: true,
      reputationToPostImages: null,
      bindNavPrevention: true,
      postfix: "",
      imageUploader: {
      brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
      contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
      allowUrls: true
      },
      noCode: true, onDemand: true,
      discardSelector: ".discard-answer"
      ,immediatelyShowMarkdownHelp:true
      });


      }
      });






      NBV Mani is a new contributor. Be nice, and check out our Code of Conduct.










       

      draft saved


      draft discarded


















      StackExchange.ready(
      function () {
      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fmechanics.stackexchange.com%2fquestions%2f61014%2firon-wires-showing-through-sidewall%23new-answer', 'question_page');
      }
      );

      Post as a guest















      Required, but never shown

























      4 Answers
      4






      active

      oldest

      votes








      4 Answers
      4






      active

      oldest

      votes









      active

      oldest

      votes






      active

      oldest

      votes








      up vote
      24
      down vote













      The "wires" you mention are likely the tire cords - essentially bands of steel wire that are major structural elements of the tire's construction. If they are exposed this is an indicator of imminent failure and the tire is dangerous to be used.



      If the cords are showing through the sidewall:





      • DO NOT drive the vehicle with that tire on!


      • DO Get the tire replaced ASAP!


      • DO NOT attempt to "remove" the cords!






      share|improve this answer





















      • You might also note that, like Paulster noted in the comments, 150,000 km is really early to be having this problem. The OP might consider looking for the underlying reason here.
        – Cullub
        yesterday






      • 3




        @Cullub according to OP, it's 15,000 km which is even earlier for this type of problem. However, it's not that early for a spare (especially if it's a compact spare), as the OP mentioned he was running. That was edited out of the OP and missed by most of us.
        – FreeMan
        13 hours ago










      • @Freeman - that's a very good point, I must confess I edited quite quickly yesterday and my initial research into the term "stepny" was unsuccessful so I left it out. I've voted to approve your edit restoring that information.
        – motosubatsu
        13 hours ago















      up vote
      24
      down vote













      The "wires" you mention are likely the tire cords - essentially bands of steel wire that are major structural elements of the tire's construction. If they are exposed this is an indicator of imminent failure and the tire is dangerous to be used.



      If the cords are showing through the sidewall:





      • DO NOT drive the vehicle with that tire on!


      • DO Get the tire replaced ASAP!


      • DO NOT attempt to "remove" the cords!






      share|improve this answer





















      • You might also note that, like Paulster noted in the comments, 150,000 km is really early to be having this problem. The OP might consider looking for the underlying reason here.
        – Cullub
        yesterday






      • 3




        @Cullub according to OP, it's 15,000 km which is even earlier for this type of problem. However, it's not that early for a spare (especially if it's a compact spare), as the OP mentioned he was running. That was edited out of the OP and missed by most of us.
        – FreeMan
        13 hours ago










      • @Freeman - that's a very good point, I must confess I edited quite quickly yesterday and my initial research into the term "stepny" was unsuccessful so I left it out. I've voted to approve your edit restoring that information.
        – motosubatsu
        13 hours ago













      up vote
      24
      down vote










      up vote
      24
      down vote









      The "wires" you mention are likely the tire cords - essentially bands of steel wire that are major structural elements of the tire's construction. If they are exposed this is an indicator of imminent failure and the tire is dangerous to be used.



      If the cords are showing through the sidewall:





      • DO NOT drive the vehicle with that tire on!


      • DO Get the tire replaced ASAP!


      • DO NOT attempt to "remove" the cords!






      share|improve this answer












      The "wires" you mention are likely the tire cords - essentially bands of steel wire that are major structural elements of the tire's construction. If they are exposed this is an indicator of imminent failure and the tire is dangerous to be used.



      If the cords are showing through the sidewall:





      • DO NOT drive the vehicle with that tire on!


      • DO Get the tire replaced ASAP!


      • DO NOT attempt to "remove" the cords!







      share|improve this answer












      share|improve this answer



      share|improve this answer










      answered yesterday









      motosubatsu

      3,2011524




      3,2011524












      • You might also note that, like Paulster noted in the comments, 150,000 km is really early to be having this problem. The OP might consider looking for the underlying reason here.
        – Cullub
        yesterday






      • 3




        @Cullub according to OP, it's 15,000 km which is even earlier for this type of problem. However, it's not that early for a spare (especially if it's a compact spare), as the OP mentioned he was running. That was edited out of the OP and missed by most of us.
        – FreeMan
        13 hours ago










      • @Freeman - that's a very good point, I must confess I edited quite quickly yesterday and my initial research into the term "stepny" was unsuccessful so I left it out. I've voted to approve your edit restoring that information.
        – motosubatsu
        13 hours ago


















      • You might also note that, like Paulster noted in the comments, 150,000 km is really early to be having this problem. The OP might consider looking for the underlying reason here.
        – Cullub
        yesterday






      • 3




        @Cullub according to OP, it's 15,000 km which is even earlier for this type of problem. However, it's not that early for a spare (especially if it's a compact spare), as the OP mentioned he was running. That was edited out of the OP and missed by most of us.
        – FreeMan
        13 hours ago










      • @Freeman - that's a very good point, I must confess I edited quite quickly yesterday and my initial research into the term "stepny" was unsuccessful so I left it out. I've voted to approve your edit restoring that information.
        – motosubatsu
        13 hours ago
















      You might also note that, like Paulster noted in the comments, 150,000 km is really early to be having this problem. The OP might consider looking for the underlying reason here.
      – Cullub
      yesterday




      You might also note that, like Paulster noted in the comments, 150,000 km is really early to be having this problem. The OP might consider looking for the underlying reason here.
      – Cullub
      yesterday




      3




      3




      @Cullub according to OP, it's 15,000 km which is even earlier for this type of problem. However, it's not that early for a spare (especially if it's a compact spare), as the OP mentioned he was running. That was edited out of the OP and missed by most of us.
      – FreeMan
      13 hours ago




      @Cullub according to OP, it's 15,000 km which is even earlier for this type of problem. However, it's not that early for a spare (especially if it's a compact spare), as the OP mentioned he was running. That was edited out of the OP and missed by most of us.
      – FreeMan
      13 hours ago












      @Freeman - that's a very good point, I must confess I edited quite quickly yesterday and my initial research into the term "stepny" was unsuccessful so I left it out. I've voted to approve your edit restoring that information.
      – motosubatsu
      13 hours ago




      @Freeman - that's a very good point, I must confess I edited quite quickly yesterday and my initial research into the term "stepny" was unsuccessful so I left it out. I've voted to approve your edit restoring that information.
      – motosubatsu
      13 hours ago










      up vote
      5
      down vote













      Sidewall damage is almost unrepairable. If it is indeed damage to the steel belts, the tire will fail violently (instantly) soon in the future.



      That's a good reason not to be trying to change it on the car, because that involves a lot of direct handling of the tire. Tires can blow from handling/maintenance, and do hurt people handling them; that's why you may see your tire shop inflate tires inside a very tough cage. If he's afraid of a new tire, do the math.. But it's pretty safe in your wheelwell. So with a structurally damaged tire, ask yourself "is this handling necessary?"



      Of course it's much more dangerous to drive the car normally at-speed and have a blowout cause a loss of control or vehice rollover.



      But don't let the chicken littles fool you, you can limp the car to the tire shop. It's vital to keep speed down to a speed where you won't lose control when the tire violently fails, 20 mph (30 kph) will be absolutely fine. If you go much faster, energy in speed is a square function, so you have a wildly increasing chance of loss of control, rollover, colliding with other cars, hurting yourself and others, and wrecking the car of course.



      Also, very important: don't just get on the main road at any speed. Don't let yourself into a situation wher you say "I am going fast because I have to", avoid those roads. Work your way through side/back streets; a longer route is fine. Choose roads where you will be able to stop immediately without disrupting traffic too badly, and once the tire is blown, you can safely handle it without fear (except of sharp edges) and put on the spare on. This will not be a normal soft tire, if you press onward for even 0.1mi (0.2km) you will quickly destroy the wheel. Road conditions won't care; I've been in places where you had to drive another 2km to get to a safe place to change a tire, and just had to let the wheel be wrecked. Don't select roads like that.






      share|improve this answer



















      • 3




        You could also use the spare...
        – Cullub
        yesterday










      • Sure, but why change it when you don't have to...
        – Harper
        22 hours ago






      • 5




        In my local jurisdiction, a good reason to fit the spare would be to avoid prosecution and a fine.
        – Steve Matthews
        19 hours ago






      • 1




        @Cullub Looks like the OP has already used the spare tire, or the "stepney" (that part has been edited out of the question). I guess that the OP does not have another spare, so using the spare is out of the question.
        – fortunate_man
        14 hours ago






      • 1




        @Harper valid points I hadn't considered. I still stand by my point with one caveat - deflate the tire first. Problem solved. Unfortunately, yelling exploding tires is not helping people overcome their DIY fear, and changing a tire is simple and can save a lot of time and money. Frankly, it strikes me as "chicken little"... Like anything in life, there are simple precautions to be taken to minimize the danger. FWIW, I did upvote your answer and did so before my comment or your response.
        – FreeMan
        13 hours ago















      up vote
      5
      down vote













      Sidewall damage is almost unrepairable. If it is indeed damage to the steel belts, the tire will fail violently (instantly) soon in the future.



      That's a good reason not to be trying to change it on the car, because that involves a lot of direct handling of the tire. Tires can blow from handling/maintenance, and do hurt people handling them; that's why you may see your tire shop inflate tires inside a very tough cage. If he's afraid of a new tire, do the math.. But it's pretty safe in your wheelwell. So with a structurally damaged tire, ask yourself "is this handling necessary?"



      Of course it's much more dangerous to drive the car normally at-speed and have a blowout cause a loss of control or vehice rollover.



      But don't let the chicken littles fool you, you can limp the car to the tire shop. It's vital to keep speed down to a speed where you won't lose control when the tire violently fails, 20 mph (30 kph) will be absolutely fine. If you go much faster, energy in speed is a square function, so you have a wildly increasing chance of loss of control, rollover, colliding with other cars, hurting yourself and others, and wrecking the car of course.



      Also, very important: don't just get on the main road at any speed. Don't let yourself into a situation wher you say "I am going fast because I have to", avoid those roads. Work your way through side/back streets; a longer route is fine. Choose roads where you will be able to stop immediately without disrupting traffic too badly, and once the tire is blown, you can safely handle it without fear (except of sharp edges) and put on the spare on. This will not be a normal soft tire, if you press onward for even 0.1mi (0.2km) you will quickly destroy the wheel. Road conditions won't care; I've been in places where you had to drive another 2km to get to a safe place to change a tire, and just had to let the wheel be wrecked. Don't select roads like that.






      share|improve this answer



















      • 3




        You could also use the spare...
        – Cullub
        yesterday










      • Sure, but why change it when you don't have to...
        – Harper
        22 hours ago






      • 5




        In my local jurisdiction, a good reason to fit the spare would be to avoid prosecution and a fine.
        – Steve Matthews
        19 hours ago






      • 1




        @Cullub Looks like the OP has already used the spare tire, or the "stepney" (that part has been edited out of the question). I guess that the OP does not have another spare, so using the spare is out of the question.
        – fortunate_man
        14 hours ago






      • 1




        @Harper valid points I hadn't considered. I still stand by my point with one caveat - deflate the tire first. Problem solved. Unfortunately, yelling exploding tires is not helping people overcome their DIY fear, and changing a tire is simple and can save a lot of time and money. Frankly, it strikes me as "chicken little"... Like anything in life, there are simple precautions to be taken to minimize the danger. FWIW, I did upvote your answer and did so before my comment or your response.
        – FreeMan
        13 hours ago













      up vote
      5
      down vote










      up vote
      5
      down vote









      Sidewall damage is almost unrepairable. If it is indeed damage to the steel belts, the tire will fail violently (instantly) soon in the future.



      That's a good reason not to be trying to change it on the car, because that involves a lot of direct handling of the tire. Tires can blow from handling/maintenance, and do hurt people handling them; that's why you may see your tire shop inflate tires inside a very tough cage. If he's afraid of a new tire, do the math.. But it's pretty safe in your wheelwell. So with a structurally damaged tire, ask yourself "is this handling necessary?"



      Of course it's much more dangerous to drive the car normally at-speed and have a blowout cause a loss of control or vehice rollover.



      But don't let the chicken littles fool you, you can limp the car to the tire shop. It's vital to keep speed down to a speed where you won't lose control when the tire violently fails, 20 mph (30 kph) will be absolutely fine. If you go much faster, energy in speed is a square function, so you have a wildly increasing chance of loss of control, rollover, colliding with other cars, hurting yourself and others, and wrecking the car of course.



      Also, very important: don't just get on the main road at any speed. Don't let yourself into a situation wher you say "I am going fast because I have to", avoid those roads. Work your way through side/back streets; a longer route is fine. Choose roads where you will be able to stop immediately without disrupting traffic too badly, and once the tire is blown, you can safely handle it without fear (except of sharp edges) and put on the spare on. This will not be a normal soft tire, if you press onward for even 0.1mi (0.2km) you will quickly destroy the wheel. Road conditions won't care; I've been in places where you had to drive another 2km to get to a safe place to change a tire, and just had to let the wheel be wrecked. Don't select roads like that.






      share|improve this answer














      Sidewall damage is almost unrepairable. If it is indeed damage to the steel belts, the tire will fail violently (instantly) soon in the future.



      That's a good reason not to be trying to change it on the car, because that involves a lot of direct handling of the tire. Tires can blow from handling/maintenance, and do hurt people handling them; that's why you may see your tire shop inflate tires inside a very tough cage. If he's afraid of a new tire, do the math.. But it's pretty safe in your wheelwell. So with a structurally damaged tire, ask yourself "is this handling necessary?"



      Of course it's much more dangerous to drive the car normally at-speed and have a blowout cause a loss of control or vehice rollover.



      But don't let the chicken littles fool you, you can limp the car to the tire shop. It's vital to keep speed down to a speed where you won't lose control when the tire violently fails, 20 mph (30 kph) will be absolutely fine. If you go much faster, energy in speed is a square function, so you have a wildly increasing chance of loss of control, rollover, colliding with other cars, hurting yourself and others, and wrecking the car of course.



      Also, very important: don't just get on the main road at any speed. Don't let yourself into a situation wher you say "I am going fast because I have to", avoid those roads. Work your way through side/back streets; a longer route is fine. Choose roads where you will be able to stop immediately without disrupting traffic too badly, and once the tire is blown, you can safely handle it without fear (except of sharp edges) and put on the spare on. This will not be a normal soft tire, if you press onward for even 0.1mi (0.2km) you will quickly destroy the wheel. Road conditions won't care; I've been in places where you had to drive another 2km to get to a safe place to change a tire, and just had to let the wheel be wrecked. Don't select roads like that.







      share|improve this answer














      share|improve this answer



      share|improve this answer








      edited 13 hours ago

























      answered yesterday









      Harper

      1,307212




      1,307212








      • 3




        You could also use the spare...
        – Cullub
        yesterday










      • Sure, but why change it when you don't have to...
        – Harper
        22 hours ago






      • 5




        In my local jurisdiction, a good reason to fit the spare would be to avoid prosecution and a fine.
        – Steve Matthews
        19 hours ago






      • 1




        @Cullub Looks like the OP has already used the spare tire, or the "stepney" (that part has been edited out of the question). I guess that the OP does not have another spare, so using the spare is out of the question.
        – fortunate_man
        14 hours ago






      • 1




        @Harper valid points I hadn't considered. I still stand by my point with one caveat - deflate the tire first. Problem solved. Unfortunately, yelling exploding tires is not helping people overcome their DIY fear, and changing a tire is simple and can save a lot of time and money. Frankly, it strikes me as "chicken little"... Like anything in life, there are simple precautions to be taken to minimize the danger. FWIW, I did upvote your answer and did so before my comment or your response.
        – FreeMan
        13 hours ago














      • 3




        You could also use the spare...
        – Cullub
        yesterday










      • Sure, but why change it when you don't have to...
        – Harper
        22 hours ago






      • 5




        In my local jurisdiction, a good reason to fit the spare would be to avoid prosecution and a fine.
        – Steve Matthews
        19 hours ago






      • 1




        @Cullub Looks like the OP has already used the spare tire, or the "stepney" (that part has been edited out of the question). I guess that the OP does not have another spare, so using the spare is out of the question.
        – fortunate_man
        14 hours ago






      • 1




        @Harper valid points I hadn't considered. I still stand by my point with one caveat - deflate the tire first. Problem solved. Unfortunately, yelling exploding tires is not helping people overcome their DIY fear, and changing a tire is simple and can save a lot of time and money. Frankly, it strikes me as "chicken little"... Like anything in life, there are simple precautions to be taken to minimize the danger. FWIW, I did upvote your answer and did so before my comment or your response.
        – FreeMan
        13 hours ago








      3




      3




      You could also use the spare...
      – Cullub
      yesterday




      You could also use the spare...
      – Cullub
      yesterday












      Sure, but why change it when you don't have to...
      – Harper
      22 hours ago




      Sure, but why change it when you don't have to...
      – Harper
      22 hours ago




      5




      5




      In my local jurisdiction, a good reason to fit the spare would be to avoid prosecution and a fine.
      – Steve Matthews
      19 hours ago




      In my local jurisdiction, a good reason to fit the spare would be to avoid prosecution and a fine.
      – Steve Matthews
      19 hours ago




      1




      1




      @Cullub Looks like the OP has already used the spare tire, or the "stepney" (that part has been edited out of the question). I guess that the OP does not have another spare, so using the spare is out of the question.
      – fortunate_man
      14 hours ago




      @Cullub Looks like the OP has already used the spare tire, or the "stepney" (that part has been edited out of the question). I guess that the OP does not have another spare, so using the spare is out of the question.
      – fortunate_man
      14 hours ago




      1




      1




      @Harper valid points I hadn't considered. I still stand by my point with one caveat - deflate the tire first. Problem solved. Unfortunately, yelling exploding tires is not helping people overcome their DIY fear, and changing a tire is simple and can save a lot of time and money. Frankly, it strikes me as "chicken little"... Like anything in life, there are simple precautions to be taken to minimize the danger. FWIW, I did upvote your answer and did so before my comment or your response.
      – FreeMan
      13 hours ago




      @Harper valid points I hadn't considered. I still stand by my point with one caveat - deflate the tire first. Problem solved. Unfortunately, yelling exploding tires is not helping people overcome their DIY fear, and changing a tire is simple and can save a lot of time and money. Frankly, it strikes me as "chicken little"... Like anything in life, there are simple precautions to be taken to minimize the danger. FWIW, I did upvote your answer and did so before my comment or your response.
      – FreeMan
      13 hours ago










      up vote
      1
      down vote













      To reiterate what Pᴀᴜʟsᴛᴇʀ2 said in the comment, such side-wall damage is not supposed to happen under normal conditions. You should try to discover what the problem was before fitting new tyres, otherwise you risk ruining those as well:




      • check the production date of your current tyres. Were they produced in 2016/2017, or much earlier? Could be the case if you got them second-hand.

      • check the camber angle. Excessive camber (which can be easily seen) may contribute to sidewall damage

      • check the load index and speed rating of your tires. With a 1.2 ton car, your tires should be at least 75S.

      • check the inflation pressure. Driving with under-inflated tyres could ruin then quite quickly.


      And yeah, once the steel cord breaks, the tyres are beyond repair and quite dangerous to drive on. On turn you take there's a risk that the cord will puncture the tyre, sending your car off the road.






      share|improve this answer



























        up vote
        1
        down vote













        To reiterate what Pᴀᴜʟsᴛᴇʀ2 said in the comment, such side-wall damage is not supposed to happen under normal conditions. You should try to discover what the problem was before fitting new tyres, otherwise you risk ruining those as well:




        • check the production date of your current tyres. Were they produced in 2016/2017, or much earlier? Could be the case if you got them second-hand.

        • check the camber angle. Excessive camber (which can be easily seen) may contribute to sidewall damage

        • check the load index and speed rating of your tires. With a 1.2 ton car, your tires should be at least 75S.

        • check the inflation pressure. Driving with under-inflated tyres could ruin then quite quickly.


        And yeah, once the steel cord breaks, the tyres are beyond repair and quite dangerous to drive on. On turn you take there's a risk that the cord will puncture the tyre, sending your car off the road.






        share|improve this answer

























          up vote
          1
          down vote










          up vote
          1
          down vote









          To reiterate what Pᴀᴜʟsᴛᴇʀ2 said in the comment, such side-wall damage is not supposed to happen under normal conditions. You should try to discover what the problem was before fitting new tyres, otherwise you risk ruining those as well:




          • check the production date of your current tyres. Were they produced in 2016/2017, or much earlier? Could be the case if you got them second-hand.

          • check the camber angle. Excessive camber (which can be easily seen) may contribute to sidewall damage

          • check the load index and speed rating of your tires. With a 1.2 ton car, your tires should be at least 75S.

          • check the inflation pressure. Driving with under-inflated tyres could ruin then quite quickly.


          And yeah, once the steel cord breaks, the tyres are beyond repair and quite dangerous to drive on. On turn you take there's a risk that the cord will puncture the tyre, sending your car off the road.






          share|improve this answer














          To reiterate what Pᴀᴜʟsᴛᴇʀ2 said in the comment, such side-wall damage is not supposed to happen under normal conditions. You should try to discover what the problem was before fitting new tyres, otherwise you risk ruining those as well:




          • check the production date of your current tyres. Were they produced in 2016/2017, or much earlier? Could be the case if you got them second-hand.

          • check the camber angle. Excessive camber (which can be easily seen) may contribute to sidewall damage

          • check the load index and speed rating of your tires. With a 1.2 ton car, your tires should be at least 75S.

          • check the inflation pressure. Driving with under-inflated tyres could ruin then quite quickly.


          And yeah, once the steel cord breaks, the tyres are beyond repair and quite dangerous to drive on. On turn you take there's a risk that the cord will puncture the tyre, sending your car off the road.







          share|improve this answer














          share|improve this answer



          share|improve this answer








          edited 18 hours ago

























          answered 19 hours ago









          Dmitry Grigoryev

          2,1551728




          2,1551728






















              up vote
              -3
              down vote













              You can not pull the steel tire belts out; You might be able to cut them with good wire cutters. Could you have picked up nails somewhere? I have pulled nails out of tread but never a side wall. In the tread, the heads have worn away so it becomes a "wire".






              share|improve this answer

























                up vote
                -3
                down vote













                You can not pull the steel tire belts out; You might be able to cut them with good wire cutters. Could you have picked up nails somewhere? I have pulled nails out of tread but never a side wall. In the tread, the heads have worn away so it becomes a "wire".






                share|improve this answer























                  up vote
                  -3
                  down vote










                  up vote
                  -3
                  down vote









                  You can not pull the steel tire belts out; You might be able to cut them with good wire cutters. Could you have picked up nails somewhere? I have pulled nails out of tread but never a side wall. In the tread, the heads have worn away so it becomes a "wire".






                  share|improve this answer












                  You can not pull the steel tire belts out; You might be able to cut them with good wire cutters. Could you have picked up nails somewhere? I have pulled nails out of tread but never a side wall. In the tread, the heads have worn away so it becomes a "wire".







                  share|improve this answer












                  share|improve this answer



                  share|improve this answer










                  answered yesterday









                  blacksmith37

                  822127




                  822127






















                      NBV Mani is a new contributor. Be nice, and check out our Code of Conduct.










                       

                      draft saved


                      draft discarded


















                      NBV Mani is a new contributor. Be nice, and check out our Code of Conduct.













                      NBV Mani is a new contributor. Be nice, and check out our Code of Conduct.












                      NBV Mani is a new contributor. Be nice, and check out our Code of Conduct.















                       


                      draft saved


                      draft discarded














                      StackExchange.ready(
                      function () {
                      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fmechanics.stackexchange.com%2fquestions%2f61014%2firon-wires-showing-through-sidewall%23new-answer', 'question_page');
                      }
                      );

                      Post as a guest















                      Required, but never shown





















































                      Required, but never shown














                      Required, but never shown












                      Required, but never shown







                      Required, but never shown

































                      Required, but never shown














                      Required, but never shown












                      Required, but never shown







                      Required, but never shown







                      Popular posts from this blog

                      flock() on closed filehandle LOCK_FILE at /usr/bin/apt-mirror

                      Mangá

                      Eduardo VII do Reino Unido