O Cantão de Berna é um cantão da Suíça, situado no centro do país. A capital é a cidade de Berna. É membro da confederação suíça desde 6 de março de 1353. Em 1 de janeiro de 1979 o cantão do Jura foi formado a partir da parte ocidental do cantão de Berna. A língua oficial deste cantão é o alemão.
Índice
1História
2Lista das Comunas
3Distritos
4Cantões
5Referências
História |
O cantão de Berna, pertence à Confederação Suíça desde 1353. Foi assim chamado de 1798 a 1815 e depois a partir 1846, mas teve outras designações como "Cidade e República de Berna" ou só "República de Berna". As línguas oficiais são o alemão e o francês mas o dialecto é Suíço-alemão (Schweizerdeutsch), e a capital é Berna.
O território passou por grandes alterações desde o fim da Idade Média: ele abarcava de 1415 a 1798 uma parte do actual cantão de Argóvia - a chamada Argóvia de Berna e de 1536 a 1798 o actual cantão de Vaud. De 1798 a 1801, foi amputado de Oberland que foi nomeado cantão com Thoune como capital. Em 1815, foi-lhe atribuído a maior parte do bispado de Basileia e Bienna que formaram juntamente com o "antigo cantão" o Jura bernense. Deste separou-se em 1978 a parte norte que se tornou no cantão do Jura.[1]
Actualmente dois terços dos habitantes reivindicam pertencer ao protestantismo[2]
O Castelo de Chillon, no Lago Lemano, está intimamente ligado com Berna, entre 1536 a 1798, no chamado Período bernense
A montanha de maior altitude deste cantão é o Finsteraarhorn com 4.274 metros de altitude.
1
This question is a follow up of this one. I am trying to run a command through the command line on a remote machine running Windows 7 from a workstation running Debian in an SSH session on that machine. The setup is basically as follows: debian box 1 === (SSH) ===> debian box 2 === (RDP) ===> Windows 7 I have tried running rdesktop from debian box 2 : rdesktop <Windows 7 box network address> -u username -p password -r disk:local="./TestRDP" -s "cmd.exe /K net use C: \\tsclientlocal & C:\test.bat & logoff" but cmd.exe is not launched on the remote device. I have also tried to open up cmd.exe on its own: rdesktop <Windows 7 box network address> -u username -p password -s "cmd.exe" but the terminal is not launched upon login ( rdesktop successf...
3
Assumed I want to draw three simple graphs based on the following illustration: How can I plot those three graphs? I've tried to create something like this: Minimum Working Example (MWE): documentclass{standalone} usepackage{pgfplots} begin{document} begin{tikzpicture} begin{axis}[domain=0:1] addplot+[no marks, samples=100] {exp(3*x)}; addplot+[no marks, samples=100] {(-exp(3*x)+20)}; end{axis} end{tikzpicture} end{document} Screenshot of the current state: Description of the issue: However, I don't get the point on how to figure out the function of the third graph as well as how to clip the graphs in x and y direction to align them centered in the plot. It is not necessary to be completely precise, the accuracy of my upper template w...
up vote
0
down vote
favorite
So, my friend has been trying to install Matlab 2018b and he has encountered the following message just after the installation reaches 100%. Matlab installation additional configuration steps message I did some digging around in the Matlab forums and found out that to use the additional components, one should install a compiler and then use the following commands: mex -setup C mex -setup C++ Can anyone help me regarding this error? If this is indeed the solution then how can I execute those steps? Also, he says that even if he presses next, he cannot use matlab. The OS in use is Windows 10.
installation matlab
share | improve this question
...